WAV Starter Kit (2 WAV’s,1 LINK Module, Power Supply)
5.595,00 kr.
Tilgængelig på restordre
En powerhead, der besvarer alle dine behov
Extreme strømning (~ 4000 + gph)
Kompakt størrelse (mindre samlede masse i forhold til næsten alle lignende flow pumper)
Retningsbestemt flow (drejer med 40 graders vifte af bevægelse og kan roteres – fantastisk til brug på bagvæggen)
Sikker, 24V DC operationLavt strømforbrug – Mindre end 35W forbrug
Flere driftstilstande (tilfældig flow tilstande, spejl, invers, etc.)
Let at rengøre (pumpe slukker automatisk, når den fjernes fra vand)
Utroligt Stille (muligvis den roligste driver på markedet)
Magnetisk mount virker på op til 2,5cm tykt glas (i en klasse for sig selv)
Nem installation med blot et enkelt tynd tråd for al magt og kontrol (1LINK interface gør det en snap!)
DIRECTIONAL FLOW ALLOWS STEALTH MOUNTING OPTIONS
Unfortunately, some of the leading water moving pumps on the market only send flow in a direction perpendicular to the glass. This really limits an aquarists options and, in some cases, obstructs the view. Having a powerhead that can be pointed in all directions is nothing new, but the hardware to make that happen usually takes up too much space and is unsightly. The WAV answers both of these problems with a new take on an articulating mount.
ENDLESS FLOW OPTIONS FOR EVERY AQUARIST
We know that everyone likes their flow a little bit different. So Apex Fusion controls the WAV with a multitude of patterned flow and random settings. You can even set one or more pumps to mirror or be the inverse of another.
DETAILED, REAL-TIME PUMP STATUS AND AI
This is a first for this product segment. From within Apex Fusion, the details of operation of every WAV on your tank can be observed. You will be able to see the mode, the RPM, the temperature range, and the current status of the pump.
SNAILS, FALLS, STALLS – NO WORRIES!
Snails and other obstructions are usually a powerhead’s worst enemy – tearing it to pieces. Sometimes just knocking a pump off the glass will not only kick up sand all over the tank, but it can also destroy the pump, or worse your favorite corals.
SAY GOODBYE TO CABLE MESS
Wires and cables are the enemy. Even so-called “wireless” devices on our aquariums have far too many cables and power supplies that clutter up our tank stands. The 1LINK system overhauls that mess of cabling by providing a way to connect up to five devices onto one power supply and make them controllable with your Apex.
There are three 1LINK source connections that can provide power and communication to WAV pumps, a DŌS, or future 1LINK devices. Additionally there are two 24V DC switched connections for future add-ons or DIY Solutions.
Do you want wireless, or less wires?
1LINK™ – EASY, ONE-CLICK INSTALLATION
The WAV is the first of a line of aquarium products from Neptune Systems that will use a completely new interface. While many in the aquarium world continue to embrace wireless technologies for interconnectivity, we have decided to go the other direction – a wire.
Wireless connectivity from your smartphone or tablet to your Apex (or other controller) is completely logical – and we embrace that. However, wireless used for the interconnecting of devices within the confines of common aquariums (that are mostly less than 6′ long) is not only unnecessary, but it reduces reliability. Our philosophy is that when distances are measured in a few feet, wireless is a solution looking for a problem. And ironically, wireless really does not save wires. You still need to use a wire to get power to the devices anyway. And let’s not forget configuration – wireless devices require syncing, endless button presses and arcane steps to get them to connect up – hopefully with you and not your neighbor. Finally for all this “benefit”, you as the consumer get the added cost of this wireless technology that must be baked into the price of every device you buy.
So after much study of the problem, our answer is 1LINK. It is called 1LINK because there is one power supply, one module (for up to three 1LINK devices), and a one-click-connection of a wire that carries not only the power for the device, but two-way communication from it to your Apex. Setup is simply click and go.
Less wires, less configuration headaches, and best of all, less cost to you as a consumer!